references/28256-eeprom.md
AT28C256 256K (32K x 8) Parallel EEPROM Specification
1. Overview
The AT28C256 is a non-volatile, electrically erasable and programmable read-only memory (EEPROM) manufactured by Atmel (now Microchip). It provides 256 Kbits of storage organized as 32,768 x 8 bits and is commonly used in 8-bit microprocessor systems such as those based on the 6502, Z80, and similar CPUs.
The device supports byte-level write operations, fast read access, and software-controlled data protection.
2. General Characteristics
| Feature | Description | | -------------- | ------------------------------ | | Memory size | 256 Kbits (32 KB) | | Organization | 32,768 x 8 bits | | Data bus | 8-bit | | Address bus | 15-bit (A0-A14) | | Technology | EEPROM | | Endurance | ≥ 100,000 write cycles | | Data retention | ≥ 10 years | | Access time | 150-250 ns (variant dependent) | | Package types | DIP-28, PLCC-32, TSOP |
3. Pin Configuration (Logical)
3.1 Address Pins (A0-A14)
- Select one of 32,768 memory locations
3.2 Data Pins (I/O0-I/O7)
- Bidirectional tri-state data bus
- Outputs valid during read cycles
3.3 Control Pins
| Pin | Description | | --- | -------------------------- | | CE | Chip Enable (active low) | | OE | Output Enable (active low) | | WE | Write Enable (active low) | | VCC | +5 V power supply | | GND | Ground |
4. Memory Organization
- Linear address space from
$0000to$7FFF - Each address corresponds to one 8-bit byte
Address Range: 0000h - 7FFFh
Data Width: 8 bits
5. Read Operation
5.1 Read Cycle Conditions
| Signal | State | | ------ | ----- | | CE | LOW | | OE | LOW | | WE | HIGH |
- Data appears on I/O pins after access time
- Output remains valid while CE and OE are asserted
- Outputs are high-impedance when CE or OE is HIGH
6. Write Operation
6.1 Byte Write Cycle
| Signal | State | | ------ | --------- | | CE | LOW | | OE | HIGH | | WE | LOW pulse |
- Address and data must be stable during WE low pulse
- Internal write cycle time ≈ 10 ms (max)
- Device automatically handles erase-before-write
7. Software Data Protection (SDP)
The AT28C256 includes optional Software Data Protection to prevent accidental writes.
7.1 SDP Enable Sequence
Write $AA to address $5555
Write $55 to address $2AAA
Write $A0 to address $5555
7.2 SDP Disable Sequence
Write $AA to address $5555
Write $55 to address $2AAA
Write $80 to address $5555
Write $AA to address $5555
Write $55 to address $2AAA
Write $20 to address $5555
8. Write Cycle Timing Notes
- Writes are internally timed; no external polling required
- During write cycle, reads return undefined data
- Device ignores additional write attempts while busy
9. Data Polling (Optional)
- I/O7 may be monitored during write
- When I/O7 matches written data, write is complete
10. Reset and Power Behavior
- No explicit reset pin
- Writes inhibited during power-up and power-down
- Outputs default to high-impedance until CE and OE asserted
11. Typical System Integration (6502 Example)
Address Range: $8000 - $FFFF
A15 used as chip select
OE R/W?
WE inverted R/W?
12. Absolute Maximum Ratings (Summary)
| Parameter | Rating | | ------------- | --------------------- | | VCC | -0.6 V to +6.25 V | | Input voltage | -0.6 V to VCC + 0.6 V | | Storage temp | -65 °C to +150 °C |
13. Variants and Compatible Devices
| Device | Notes | | ---------------- | ---------------------------- | | AT28C256 | Original Atmel | | AT28C256F | Faster access time | | SST28SF256 | Flash-compatible alternative | | 28C256 (generic) | Common pin-compatible EEPROM |
14. Common Use Cases
- ROM replacement in retro systems
- Firmware storage
- Microcomputer monitors and BASIC ROMs
- Prototyping and hobbyist computers
15. References
- https://www.utmel.com/components/at28bv256-eeproms-pinout-equivalent-and-datasheet?id=1019
- https://www.futurlec.com/Memory/28C256.shtml
- https://ww1.microchip.com/downloads/en/DeviceDoc/doc0006.pdf
- https://bread80.com/2020/08/10/the-ben-eater-eeprom-programmer-28c256-and-software-data-protection/